Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit comes with LONG SHAFT pots, which is appropriate for the following guitars: ALL production Les Pauls® made since 1977. This kit is for USA guitars not Historic® series guitars - Gibson Historics (R4, R6, R7, R8, R9, R0) use short-shaft pots.

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.

Les Paul Studio's use long shaft pots, but a short/straight switch. If ordering a kit for your Les Paul Studio, select the short/straight switch.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: all guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

Whats in the kit:
(2) 500K RS Long Shaft SuperPots®. We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position. A smoother resistor path make this the best pot to ever be used in the guitar.

(2) 500K CTS Long Shaft Audio taper pots.

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-bus wire - Used for the grounding in the circuit.

(1) 4-foot length braided wire - Used for wiring switch.

(1) Short or Long 3-way toggle switch - Manufactured by Switchcraft®.

(1) 1/4 Jack - Manufactured by Switchcraft®.

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit comes with SHORT SHAFT pots, which is appropriate for the following guitars: ALL GUITARS with the exception of all production Les Pauls® made since 1977. For owners of Historic® Les Pauls, this kit is for you!

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.
  
Whats in the kit: 
(2) 500K RS Short-Shaft SuperPots®. We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position. A smoother resistor path make this the best pot to ever be used in the guitar.

(2) 500K CTS Short-Shaft Audio taper pots.

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-bus wire - Used for the grounding in the circuit.  

(1) 4-foot length braided wire - Used for wiring switch.  

(1) Long 3-way toggle switch - Manufactured by Switchcraft®.  

(1) 1/4"-inch Jack - Manufactured by Switchcraft®.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Strat® style guitars. Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.

Whats in the kit:

(1) 280K RS Split-Shaft SuperPot®. We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.

(2) 250K CTS Split-Shaft Audio taper pots- Audio taper pots work great for tone controls. With that in mind, we had CTS improve their stock audio taper pot by using brass shaft construction (brass is much more resilient than the typical aluminum,) and much tighter tolerances.

(1) Vintage RS GuitarCap Paper In Oil .047µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-white wire - Used for the grounding and wiring the switch in the circuit.

(1) Length vintage black wire - Also used for the grounding and wiring the switch in the circuit.

(1) Swithcraft® output jack - Made in the USA.

(1) CRL® 5-Way switch - Made in the USA.

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Please Note: ALL 280K SuperPots are SPLIT-SHAFT. When you order a Tele/Esquire kit, it will ship with brass sleeves for use with knobs with set screws. All standard USA Tele-style knobs will fit over the brass sleeves; knobs with set-screws should accept a 1/4"-inch shaft. Please contact us with any questions or concerns.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Tele®/Esquire® style guitars.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; Please call us for details or questions about installation.

What's in the kit:
(1) 280K RS SuperPot®. We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.

(1) 250K CTS Solid Shaft Audio taper pots- Audio taper pots work great for tone controls. With that in mind, we had CTS improve their stock audio taper pot by using brass shaft construction (brass is much more resilient than the typical aluminum,) and much tighter tolerances.

(1) Vintage RS GuitarCap Paper In Oil .047µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Polyester film .0047µF capacitor for the RS Esquire 'cocked wah' mod.

(1) Length vintage white wire - Used for grounding and the wiring of the switch in the circuit.

(1) Length vintage black wire - Used for grounding and wiring the switch in the circuit.

(1) Switchcraft® input jack - Made in the USA.

(1) CRL® 3 way switch - Made in the USA.

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Add out-of-phase, coil-split, series-parallel...modify a kit for a unique guitar, even re-wire a Gretsch... call in or email sales@rsguitarworks.net for other options...

Once added to the shopping cart, in the 'Order Notes' box, indicate specific wiring desired, etc. Mini switches available - please call or email.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit comes with LONG SHAFT pots, which is appropriate for the following guitars: All production Les Pauls® made since 1977. This does NOT include the Historic® series. If your guitar has a large Maple cap, then this kit is for you.

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.
 
What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.
 
What's in the kit: 
(2) 500K RS Long-Shaft SuperPots®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.
  
(2) 500K CTS Long-Shaft Audio taper pots. 

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length bus wire- Used for the grounding in the circuit.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit comes with SHORT SHAFT pots, which is appropriate for the following guitars: ALL GUITARS with the exception of all production Les Pauls® made since 1977. For owners of Historic® Les Pauls, this kit is for you!

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.  

What's in the kit: 
(2) 500K RS Short-Shaft SuperPots®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.  

(2) 500K CTS Short-Shaft Audio taper pots. 

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length bus wire- Used for the grounding in the circuit.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

The Vintage Explorer/Flying V Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Gibson Explorer®/Flying V® style guitars, no matter what the pickup combination is.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.
  
What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.  

What's in the kit: 
(2) 500K RS Short-Shaft SuperPots®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.
  
(1) 500K CTS Short-Shaft Audio taper pot. 

(1) Vintage RS GuitarCap Paper In Oil .022µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-black wire - Used for the grounding in the circuit.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Due to supply chain issues at CTS, we are out-of-stock on the short-shaft 500K SuperPot Volumes. Until further notice, for Volume controls in the short-shaft 500K kits, we will use a CTS audio taper pot based off a 50’s CentraLab pot, which has a better taper than current audio taper pots.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who want to maintain clarity while rolling their controls down without increasing any brightness!! This kit comes with SHORT SHAFT pots for a Gibson Firebird®.

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.
  
What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.
 
What's in the kit:  
(2) 500K RS Short-Shaft SuperPots®. We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position. A smoother resistor path make this the best pot to ever be used in the guitar.  

(2) 500K CTS Short-Shaft Audio taper pot.

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

 

(1) Length black vintage wire- Used for the grounding the circuit.  

(1) 4-foot length braided wire- Used for wiring switch.  

(1) Long-thread/short-ground jack for Firebird.  

(1) 90 degree 3-position switch - Made by Switchcraft® in the United States, this is the best 3-way switch on the market.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Please Note: ALL 280K SuperPots are SPLIT-SHAFT. When you order a Jazz Bass kit, it will ship with brass sleeves for use with knobs with set screws. All standard USA Jazz Bass-style knobs will fit over the brass sleeves; other knobs with set-screws should accept a 1/4"-inch shaft. Please contact us with any questions or concerns.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your bass effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Fender Jazz Bass® style basses, no matter what the pickup combination is.

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What this is: For years, guitar/bass manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line models. This kit is designed to utilize the best electronic components possible in your bass. This kit is the culmination of thousands of hours of research and development into different bass electronics and how each of them affects the overall tone of the bass.
  
What's in the kit: 
(2) 280K RS Solid-Shaft SuperPots® - We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this 
the best pot to ever be used in the guitar.  

(1) 250K CTS Solid-Shaft Audio taper pot.

(1) Vintage RS GuitarCap Paper In Oil .047µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-white wire - Used for wiring the circuit.

(1) Length vintage-black wire - Used for the grounding the circuit.  

(1) Output Jack- Manufactured by Switchcraft®.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your bass, you will achieve tones that you didn't think were possible.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Les Paul Jr.® style guitars, no matter what the pickup combination is.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.

What's in the kit:
(1) 500K RS Short-Shaft SuperPots®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.

(1) 250K CTS Short-Shaft Audio taper pot.

(1) Vintage RS GuitarCap Paper In Oil .022µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-black wire- Used for the grounding in the circuit. 

Please Note: ALL 280K SuperPots are SPLIT-SHAFT. When you order a Precision Bass kit, it will ship with brass sleeve for use with knobs with set screws. All standard USA Tele-style knobs will fit over the brass sleeves; other knobs with set-screws should accept a 1/4"-inch shaft. Please contact us with any questions or concerns.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your bass effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Fender Precision Bass® style basses. Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.
 
What this is: For years, guitar/bass manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line models. This kit is designed to utilize the best electronic components possible in your bass. This kit is the culmination of thousands of hours of research and development into different bass electronics and how each of them affects the overall tone of the bass. 

What's in the kit: 
(1) 280K RS Solid-Shaft SuperPot® - We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.  

(1) 250K CTS Solid Shaft Audio taper pots - Audio taper pots work great for tone controls. With that in mind, we had CTS improve their stock audio taper pot by using brass shaft construction (brass is much more resilient than the typical aluminum,) and much tighter tolerances. 

(1) Vintage RS GuitarCap Paper In Oil .047µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage white wire - Used for wiring the circuit.

(1) Length vintage black wire - Used for grounding the circuit.

(1) Switchcraft® 1/4" jack - Made in the USA.

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your bass, you will achieve tones that you didn't think were possible.

The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!!

This kit is designed for all PRS® style guitars. Most set-neck versions of these guitar use the 90 degree switch; bolt-on versions use the short/straight switch. NOTE: The short/straight switch will work for all model gutiars, so if you have doubts as to what is in your guitar, go with the short/straight option. Please Note: With any PRS® model other than the McCarty or McCarty wired guitars you will have to enlarge the rotary switch hole to 1/2" for the toggle switch to fit. Also be aware that some knowledge of basic wiring is needed as PRS® does not use the same color codes on rotary guitars as used on the McCarty.

Available in left-handed orientation with correct-turning pots. Not just wired backwards, but the correct taper as well!! NO EXTRA CHARGE !!

Please note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.

What's in the kit:
(1) 500K RS Short-Shaft SuperPot®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.

(1) 500K CTS Push-Pull Audio taper pot- Audio taper pots work great for tone controls. This pot gives you the coil tap option that is needed in PRS® style guitars.

(1) Vintage RS GuitarCap Paper In Oil .022µF Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length vintage-black wire- Used for the grounding in the circuit.

(1) Length vintage-white wire. Used for the signal in the circuit.

(1) 3-position Short or 90º Toggle switch - Made by Switchcraft® in the United States, this is the best 3-way switch on the market.

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!!

Available in 3 styles:

• Classic: uses two .022µF caps for both Tone controls.

• Classic - Woman Tone: uses one .01µF in the Neck Tone for better clarity in the Neck pickup, and one .022µF in the Bridge Tone.

• Classic - Fat: uses one .022µF in the Neck Tone, and one .033 in the Bridge Tone for a fatter tone with the Bridge Tone and pickup.

  
What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar. Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly. Also, metric knobs will not fit the RS pot shafts; most popular knobs are available on the store in new and aged versions. Please call us for details or questions about installation.

What's in the kit: 
(2) 500K RS Short-Shaft SuperPots®- We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not loose any clarity, even in the neck position. A smoother resistor path make this the best pot to ever be used in the guitar.
  
(2) 500K CTS Short-Shaft Audio taper pots. 

(2) Vintage RS GuitarCap Paper In Oil Capacitor. Manufactured to RS specs, these hand-made 100v caps have a rich vintage tone, while still retaining open top-end clarity. Hand-wound on 50's-era machines, the new RS Vintage GuitarCaps use vintage-correct Kraft paper, solid military-spec construction and tinned 20AWG leads for easy soldering. They really hold their own against the vintage caps; their tone is similar to the famous caps from the 50's.

(1) Length black vintage wire - Used for the grounding the circuit.  

(1) 2-foot length braided wire - Used for wiring switch.  

(1) Long-thread/short-ground jack for SG. 

(1) 90 Degree 3-way toggle switch - Manufactured by Switchcraft®.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.

Please Note: ALL 280K SuperPots are SPLIT-SHAFT. When you order a Tele/Esquire kit, it will ship with brass sleeves for use with knobs with set screws. All standard USA Tele-style knobs will fit over the brass sleeves; other knobs with set-screws should accept a 1/4"-inch shaft. Please contact us with any questions or concerns.

Who this kit is for: The Vintage Upgrade Kits offer a warmer, woody tone for anyone who is tired of not being able to use the controls on your guitar effectively. This kit is also great for those who are tired of losing tone and note-definition every time they roll their control past 8!! This kit is designed for all Tele®/Esquire® style guitars.

Please Note: All guitars manufactured in Japan, China, Indonesia and Mexico use metric pots (6mm), and have metric sized holes drilled for the pots. All pots sold by RS Guitarworks use standard pots and hole diameters (3/8"). Therefore, holes in the guitar, plates and/or pickguards will need to be enlarged to 3/8" to fit properly Also, metric knobs will not fit the RS pot shafts; Please call us for details or questions about installation.
 
What this is: For years, guitar manufacturers have chosen to cut corners on the electronics they have used, even in their top-of-the-line guitars. This kit is designed to utilize the best electronic components possible in your guitar. This kit is the culmination of thousands of hours of research and development into different guitar electronics and how each of them affects the overall tone of the guitar.
 
What's in the kit: 
(1) 280K RS SuperPot® - We designed these pots in conjunction with CTS. Used for the volume controls in the kit, these pots have a custom taper that gives you a noticeable difference between each number on your volume control. You can finally roll your volume down to 2 or 1 and not lose any clarity, even in the neck position!! Mil-spec construction and a smoother resistor path make this the best pot to ever be used in the guitar.
  
(1) 250K CTS Solid Shaft Audio taper pots- Audio taper pots work great for tone controls. With that in mind, we had CTS improve their stock audio taper pot by using brass shaft construction (brass is much more resilient than the typical aluminum,) and much tighter tolerances.

(1) Vintage RS GuitarCap Paper In Oil .047µF. RS is proud to bring you our new Vintage 600 volt Paper In Oil (PIO) capacitor. We have tested these against some of the best new and vintage caps on the market and we are happy to say they outperformed any cap we have sold in the past and they really hold their own against the vintage caps. Their sound is just like the caps from the 50's.

(1) Polyester film .0047µF capacitor for the RS Esquire 'cocked wah' mod.

(1) Length vintage white wire - Used for grounding and the wiring of the switch in the circuit.  

(1) Length vintage black wire - Used for grounding and wiring the switch in the circuit.  

(1) Color wiring diagram.

How this kit improves your tone: All of the above components combine to create unprecedented clarity in your overall tone. This increase in clarity will also equate to an increase in note bloom, harmonic complexity, and, in some cases, sustain. Because this kit increases the usability and intuitiveness of the controls onboard your guitar, you will achieve tones that you didn't think were possible.